Features:

• Works with all major receiver brands including Spektrum, Futaba, Hitec, JR, and more.
• 3 Pre-programmed flight modes:
• • Normal Mode (2D Mode): this is the standard flight stabilization mode.

  • 3D Flight Mode: this mode will attempt to hold the LAST position the aircraft was in. For example, if you put the airplane into a knife edge and then activate 3D mode, the airplane will hold the knife edge.

  • Gyro Deactivated Mode: this turns the gyro off to allow unassisted non-stabilized flight.

  • • 3 Wing Types: standard, delta, and v-tail.
    • One-key setting mode with colored LED indicator light
    • Remote master gain
    • Supports 50Hz, 125Hz, and 250Hz servo frequencies
    • Separate gain adjustment for each flight mode
    • Automatic gyro calibration (auto stick centering) at start-up
    • High Voltage (7.4v) compatible
    • Futaba S.Bus and S.Bus 2 compatible
    • Easy to use, extremely well-suited to beginners.
    • small, lightweight form-factor

    • Includes:

      • Eagle A3-L Flight Stabilizer
      • 16V EZ-Plug capacitor to help maintain a secure voltage level during flight
      • 3M Foam mounting tape
      • 4 x 150mm(6 ) male to male servo wires to connect stabilizer to your receiver

      • Specifications:

        • Input Voltage: DC 5V-7.4V, powered from the receiver directly
        • Gyroscope: 2000 dps, 1kHz
        • Servo Frequency: 50Hz 125Hz 250Hz
        • Servo Travel: 1520500s Limit 970-2070s
        • Operating Temperature: -40 ℃ to 85 ℃
        • Size: 43mm x 27mm
        • Weight: 11 g (excluding wires)

        • Which Eagle Gyro is right for me?

          Sensor

          2D Mode

          3D Mode

          Auto-Recovery

          Auto-Hover

          Remote Gain

          S.Bus

          HV

          Upgradable

          Price

          A3-L

          3-Axis

          ✔

          ✔

          ✔

          ✔

          ✔

          $

          A3 Pro

          6-Axis

          ✔

          ✔

          ✔

          ✔

          ✔

          ✔

          ✔

          $$

          A3 Super 3

          6-Axis

          ✔

          ✔

          ✔

          ✔

          ✔

          ✔

          ✔

          ✔

          $$$

           

          IMPORTANT – Please Read This Carefully

          • Proper setup of the Hobby Eagle Gyro is crucial. Read the gyro instruction manual completely before attempting to fly your aircraft. Failure to follow setup instructions can result in loss of control and inevitable damage to your aircraft.
          • Ensure the gyro is installed in the proper orientation (see manual) and is mounted to a hard surface near the aircraft s CG point.
          • When you first plug in your aircraft battery DO NOT move your aircraft for at least 10 seconds to allow the gyro to perform self-calibration.
          • It is crucial to verify that the gyro is moving the control surfaces in the correct direction BEFORE attempting to fly your aircraft. Failure to do so could result in loss of control during flight.
          • Setup one of your gyro control switches (3 position switch on your radio) to activate Gyro Disable. This safety feature will allow you turn off the gyro if you encounter any issues during flight.
          • ANY warranty claim for Hobby Eagle gyros applies to the gyro only, not the aircraft in which the gyro was installed.

          • Wiring

            The new A3 series provides 5-channel inputs and 3-channel outputs. You only need to connect the receiver and servos to the corresponding pins on the side of the controller. The knobs are used to adjust the gain for each flight mode, clockwise to increase, anti-clockwise to decrease. Futaba s S.Bus and S.Bus 2 are supported by the new A3 series.

            

            

            

            A3-L Setting Menu

            When the controller is working, press and hold down the button for more than 2 seconds which will allow you to enter the settings menu as all settings are completed by the button. Please consult the manual for more details.

            

            Package Contents

            The box contains 4 receiver wires and 2 pieces of double-sided tape in addition to the A3.

            

          Title	Default